Retractable Turntable Industrial Parts Washer
The StingRay 10073 parts washer is engineered to provide the cleaning capacity to handle extremely large industrial parts cleaning loads. The impressive work area can even handle a complete Caterpillar 3516 engine in the horizontal position for pre-washing before tear down. Additional industrial parts washing applications include cleaning gear drives & cases, precision gears, and torque arms from wind turbines, cranes, bridges, mining equipment and satellite antenna drives for rebuilding and repair.
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 1/4" Sheet Steel Cabinet Thickness
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
100 inches |
2540 mm |
| Work Height: |
73 inches |
1850 mm |
|
Table Load Capacity:
|
10,000 lbs |
4530 kg |
| Heavy Duty Capacity: |
20,000 lbs |
9060 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
156 inches |
3960 mm |
| Depth: (Std Unit) |
132 inches |
3350 mm |
| Height: |
137 inches |
3470 mm |
| Empty Weight: |
18,400 lbs |
8350 kg |
| Reservoir Capacity: |
1035 gallons |
3918 liters |
| Duplex Reservoir: |
Add 56 gallons |
Add 212 liters |
| Sludge Capacity: |
260 gallons |
984 liters |
| Spray Blast Manifold: |
| OSCILLATING NON-SYNCHRONOUS Video |
| Angle of Oscillation: (Picture) |
40 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
24 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
90-120 minutes |
90-120 minutes |
| Electric Heat Element Size: (Picture)** |
120 kW |
120 kw |
| Gas / Propane (Picture) |
950,000 BTU/hr |
249 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
Across the Line |
| Short Circuit Protection: |
Std |
Std |
| Overload Protection: |
Std |
Std |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
|
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| Standard: |
30 hp (US) |
22 kW (Metric) |
| Total System Flow: |
343 gpm |
1300 l/min |
| Flow per Nozzle: |
14.3 gpm |
54 l/min |
| System Pressure: |
121 psi |
8.3 bar |
| Blast Velocity: |
133 ft/sec |
41 m/sec |
| Power Density: |
0.09 hp/ft³ |
2 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
70 hp (US) |
52 kW (Metric) |
| Total System Flow: |
399 gpm |
1510 l/min |
431 gpm |
1630 l/min |
| Flow per Nozzle: |
16.6 gpm |
63 l/min |
18 gpm |
68 l/min |
| System Pressure: |
163 psi |
11.2 bar |
190 psi |
13.1 bar |
| Blast Velocity: |
155 ft/sec |
47 m/sec |
168 ft/sec |
51 m/sec |
| Power Density: |
0.17 hp/ft³ |
4 kW/m³ |
0.21 hp/ft³ |
5 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
