Retractable Turntable Parts Washers
The StingRay 3040 industrial parts washer is engineered for cleaning automotive engines, transmissions, electrical motors, bearings and other components. The StingRay 3040 Parts Washer can prewash a complete engine prior to rebuild. The high power density and high temperature aqueous wash cycle makes it popular for cleaning gasoline engine heads and engine component parts plus aircraft bearings for recycling. It is perfect for new manufacturing applications where work cells need a closed loop parts washer that can wash, fresh water rinse, apply rust inhibitor and dry parts without discharging solution in the work area.
Standard Features & General Construction:
- Green Technology: Closed Loop Zero Discharge
- Heavy 7 gauge (3/16 inch) thick cabinet walls and reservoir
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 3/16" Sheet Steel Cabinet Thickness
- 208V, 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- 50 Hertz 380V and other worldwide voltages available
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
30 inches |
760 mm |
| Work Height: |
40 inches |
1010 mm |
|
Table Load Capacity:
|
1000 lbs |
453 kg |
| Heavy Duty Capacity: |
1500 lbs |
680 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
67 inches |
1702 mm |
| Depth: (Std Unit) |
63 inches |
1600 mm |
| Height: |
80 inches |
2032 mm |
| Empty Weight: |
3150 lbs |
1430 kg |
| Reservoir Capacity: |
130 gallons |
492 liters |
| Duplex Reservoir: |
Add 47 gallons |
Add 178 liters |
| Sludge Capacity: |
37 gallons |
140 liters |
| Spray Blast Manifold: |
OSCILLATING NON-SYNCHRONOUS
|
| Angle of Oscillation: (Picture) |
39 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
16 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
60-90 minutes |
60-90 minutes |
| Electric Heat Element Size: (Picture)** |
30 kW |
30 kw |
| Gas / Propane (Picture) |
180,000 BTU/hr |
53 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
Across the Line |
| Short Circuit Protection: |
Std |
Std |
| Overload Protection: |
Std |
Std |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
|
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| STANDARD: |
10 hp (US) |
7.5 kW (Metric) |
| Total System Flow: |
180 gpm |
681 l/min |
| Flow per Nozzle: |
11.3 gpm |
43 l/min |
| System Pressure: |
75 psi |
5.2 bar |
| Blast Velocity: |
105 ft/sec |
32 m/sec |
| Power Density: |
0.61 hp/ft³ |
14 kW/m³ |
| UPGRADES: (SIMPLEX) |
20 hp (US) |
15 kW (Metric) |
30 hp (US) |
22 kW (Metric) |
40 hp (US) |
30 kW (Metric) |
| Total System Flow: |
221 gpm |
835 l/min |
256 gpm |
979 l/min |
268 gpm |
1013 l/min |
| Flow per Nozzle: |
13.8 gpm |
52 l/min |
16.0 gpm |
61 l/min |
16.8 gpm |
64 l/min |
| System Pressure: |
112 psi |
7.7 bar |
152 psi |
10.5 bar |
165 psi |
11.4 bar |
| Blast Velocity: |
129 ft/sec |
39 m/sec |
150 ft/sec |
46 m/sec |
156 ft/sec |
48 m/sec |
| Power Density: |
1.22 hp/ft³ |
29 kW/m³ |
1.83 hp/ft³ |
143 kW/m³ |
2.44 hp/ft³ |
58 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
| Total System Flow: |
303 gpm |
1145 l/min |
| Flow per Nozzle: |
18.9 gpm |
72 l/min |
| System Pressure: |
212 psi |
14.6 bar |
| Blast Velocity: |
177 ft/sec |
54 m/sec |
| Power Density: |
3.36 hp/ft³ |
28 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
