Retractable Turn Table Parts Washer
The StingRay 3055 Aqueous Parts Cleaning machine is engineered for cleaning engines, transmissions, and components in automotive shops. The StingRay 3055 Parts Washer can pre-wash a complete engine prior to remanufacture in less than 6 minutes. The high parts cleaning power makes it popular for cleaning engine heads and components and electric motors and bearings for rebuilding. The SR3055 parts washer is perfect for new manufacturing cleaning applications where work cells need a closed loop industrial parts washer that can wash, fresh water rinse and apply Rust Inhibitor without discharging solution in the work area.
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge
- Heavy 7 gauge (3/16 inch) thick cabinet walls and reservoir
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 3/16" Sheet Steel Cabinet Thickness
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- 50 Hertz 380V and other worldwide voltages available
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
30 inches |
760 mm |
| Work Height: |
55 inches |
1397 mm |
| Table Load Capacity: |
1000 lbs |
453 kg |
| Heavy Duty Capacity: |
1500 lbs |
680 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
67 inches |
1702 mm |
| Depth: (Std Unit) |
63 inches |
1600 mm |
| Height: |
95 inches |
2413 mm |
| Empty Weight: |
3550 lbs |
1610 kg |
| Reservoir Capacity: |
130 gallons |
192 liters |
| Duplex Reservoir: |
Add 47 gallons |
Add 178 liters |
| Sludge Capacity: |
37 gallons |
140 liters |
| Spray Blast Manifold: |
OSCILLATING NON-SYNCHRONOUS
|
| Angle of Oscillation: (Picture) |
39 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
20 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
60-120 minutes |
60-120 |
| Electric Heat Element Size: (Picture)** |
30 kW |
30 kw |
| Gas / Propane (Picture) |
180,000 BTU/hr |
53 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
Across the Line |
| Short Circuit Protection: |
Std |
Std |
| Overload Protection: |
Std |
Std |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
|
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| STANDARD: |
20 hp (US) |
15 kW (Metric) |
| Total System Flow: |
269 gpm |
1020 l/min |
| Flow per Nozzle: |
13.5 gpm |
51 l/min |
| System Pressure: |
107 psi |
7.4 bar |
| Blast Velocity: |
126 ft/sec |
38 m/sec |
| Power Density: |
0.89 hp/ft³ |
21 kW/m³ |
| UPGRADES: (SIMPLEX) |
30 hp (US) |
22 kW (Metric) |
40 hp (US) |
30 kW (Metric) |
| Total System Flow: |
301 gpm |
1140 l/min |
319 gpm |
1210 l/min |
| Flow per Nozzle: |
15.1 gpm |
57 l/min |
16.0 gpm |
61 l/min |
| System Pressure: |
134 psi |
9.2 bar |
150 psi |
10.3 bar |
| Blast Velocity: |
141 ft/sec |
43 m/sec |
149 ft/sec |
45 m/sec |
| Power Density: |
1.06 hp/ft³ |
31 kW/m³ |
1.41 hp/ft³ |
42 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
70 hp (US) |
52 kW (Metric) |
| Total System Flow: |
356 gpm |
1350 l/min |
371 gpm |
1400 l/min |
| Flow per Nozzle: |
17.8 gpm |
67 l/min |
18.6 gpm |
70 l/min |
| System Pressure: |
187 psi |
13 bar |
203 psi |
14 bar |
| Blast Velocity: |
166 ft/sec |
51 m/sec |
173 ft/sec |
53 m/sec |
| Power Density: |
1.94 hp/ft³ |
58 kW/m³ |
2.47 hp/ft³ |
73 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
