Retractable Turntable Industrial Parts Washer
The StingRay 4040 Aqueous Parts Washer is engineered for cleaning over-road truck transmission and carrier rebuilders. The versatile design of the StingRay 4040 provides excellent cleaning power and short wash cycles for heavy duty soils. This industrial parts washer is very popular for cleaning and degreasing engines and transmissions in truck component and off-road rebuilders like Caterpillar and Komatsu, as well as many rail shops for brake and power pack rebuilding. It is also available with an extended 63" work height for washing taller parts.
Standard Features & General Construction:
- Green Technology: Closed Loop Zero Discharge
- Heavy 7 gauge (3/16 inch) thick cabinet walls and reservoir
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 3/16" Sheet Steel Cabinet Thickness
- 208V, 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- 50 Hertz 380V and other worldwide voltages available
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
41 inches |
1040 mm |
| Work Height: |
39 inches |
990 mm |
|
Table Load Capacity:
|
1500 lbs |
680 kg |
| Heavy Duty Capacity: |
3500 lbs |
1590 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
79 inches |
2000 mm |
| Depth: (Std Unit) |
74 inches |
1870 mm |
| Height: |
83 inches |
2100 mm |
| Empty Weight: |
3900 lbs |
1770 kg |
| Reservoir Capacity: |
180 gallons |
681 liters |
| Duplex Reservoir: |
Add 47 gallons |
Add 178 liters |
| Sludge Capacity: |
47 gallons |
178 liters |
| Spray Blast Manifold: |
OSCILLATING NON-SYNCHRONOUS
|
| Angle of Oscillation: (Picture) |
39 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
16 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
60-90 minutes |
60-90 minutes |
| Electric Heat Element Size: (Picture)** |
30 kW |
30 kw |
| Gas / Propane (Picture) |
180,000 BTU/hr |
53 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
IEC Type 2 |
| Short Circuit Protection: |
Std |
Coordinated |
| Overload Protection: |
Std |
Thermal Class 10 |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
NFPA 79 |
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient NEMA MG-1 |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| STANDARD: |
10 hp (US) |
7.5 kW (Metric) |
| Total System Flow: |
180 gpm |
681 l/min |
| Flow per Nozzle: |
11.3 gpm |
43 l/min |
| System Pressure: |
75 psi |
5.2 bar |
| Blast Velocity: |
105 ft/sec |
32 m/sec |
| Power Density: |
0.34 hp/ft³ |
8 kW/m³ |
| UPGRADES: (SIMPLEX) |
20 hp (US) |
15 kW (Metric) |
30 hp (US) |
22 kW (Metric) |
40 hp (US) |
30 kW (Metric) |
| Total System Flow: |
221 gpm |
835 l/min |
256 gpm |
979 l/min |
268 gpm |
1010 l/min |
| Flow per Nozzle: |
13.8 gpm |
52 l/min |
16.0 gpm |
61 l/min |
16.8 gpm |
64 l/min |
| System Pressure: |
112 psi |
7.7 bar |
152 psi |
10.5 bar |
165 psi |
11.4 bar |
| Blast Velocity: |
129 ft/sec |
39 m/sec |
150 ft/sec |
46 m/sec |
156 ft/sec |
48 m/sec |
| Power Density: |
.71 hp/ft³ |
17 kW/m³ |
1.06 hp/ft³ |
25 kW/m³ |
1.41 hp/ft³ |
33 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
| Total System Flow: |
303 gpm |
1150 l/min |
| Flow per Nozzle: |
18.9 gpm |
72 l/min |
| System Pressure: |
212 psi |
14.6 bar |
| Blast Velocity: |
177 ft/sec |
54 m/sec |
| Power Density: |
1.94 hp/ft³ |
46 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
