5248 StingRay Parts Washer

Retractable Turntable Heavy Duty Parts Washer

The StingRay 5248 aqueous parts washer is engineered for tough cleaning applications. The large heavy duty 52" diameter turntable machine is heavy duty and features high parts washer power density for removing paint, oil, grease, hydrocarbon deposits and more. Used in rail, over the road and off road rebuilding of engines, transmissions and associated parts. Automated aqueous parts washer utilizes unique oscillating spray manifold and high pressure to overpower the soils.

Standard Features & General Construction:

• Green Technology: Closed Loop Zero Discharge
• Heavy 7 gauge (3/16 inch) thick cabinet walls and reservoir
• Swing Door Retracting Turntable for Maximum Access
• Electronic Water Level Control & Refill
• Oscillating Wash Manifold to Maximize Cleaning
• Easy to Service Front Wash Pump Suction Strainer
• Adjustable Electronic Temp Control, Temp Gauge
• Control Transformer External of Panel minimizes Heat
• Programmable 24 Hour 7 Day Clock
• Low Water Shut-off Protects Pumps & Heating System
• Electronic Door Safety Interlock
• Wash Cycle Timer with Auto Reset
• Heavy gauge 3/16" Sheet Steel Cabinet Thickness
• 208V, 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
• 50 Hertz 380V and other worldwide voltages available
• Chemical Resistant Two Part 3 mil Epoxy Coating

 

Work Area Dimensions:	US	Metric
Turntable Diameter:	52 inches	1320 mm
Work Height:	48 inches	1210 mm
Table Load Capacity:	2500 lbs	906 kg
Heavy Duty Capacity:	7000 lbs	2720 kg

Overall Dimensions:	US	Metric
Width: (Std Unit)	98 inches	2480 mm
Depth: (Std Unit)	87 inches	2200 mm
Height:	93 inches	2360 mm
Empty Weight:	5800 lbs	2630 kg
Reservoir Capacity:	265 gallons	1003 liters
Duplex Reservoir:	Add 47 gallons	Add 178 liters
Sludge Capacity:	75 gallons	284 liters

Spray Blast Manifold:
OSCILLATING NON-SYNCHRONOUS
Angle of Oscillation: (Picture)	39 Degrees
Frequency of Oscillation:	4 per minute
Number of Wash Nozzles: (Picture)	20
Type of Nozzle:	V-Jet
Nozzle Material:	316 Stainless

Heating System:	US	Metric
Operating Temperature:	140-190 degrees F	60-88 degrees C
Initial Heat up Time:	60-90 minutes	60-90 minutes
Electric Heat Element Size: (Picture)**	60 kW	60 kw
Gas / Propane (Picture)	400,000 BTU/hr	117 kW

Electrical Panel (Picture)	US	Metric
Motor Starters:	Across the Line	IEC Type 2
Short Circuit Protection:	Std	Coordinated
Overload Protection:	Std	Thermal Class 10
Electrical Enclosures:	NEMA 12	IP65
Wiring Standard:	NFPA 79	NFPA 79
Wiring Conduit:	Flex-Non-Metallic	Flex-Non-Metallic
Conduit Type:	Liquidtight Nema 12	Liquidtight IP65

Pump System & Performance:
Motor Type: (Picture)	Energy-Efficient
Motor Rating:	Continuous Duty
Motor Enclosures:	TEFC

High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.

STANDARD:	20 hp (US)	15 kW (Metric)
Total System Flow:	269 gpm	1020 l/min
Flow per Nozzle:	13.5 gpm	51 l/min
System Pressure:	107 psi	7.4 bar
Blast Velocity:	126 ft/sec	38 m/sec
Power Density:	0.34 hp/ft³	8 kW/m³

 

UPGRADES: (SIMPLEX)	30 hp (US)	22 kW (Metric)	40 hp (US)	30 kW (Metric)
Total System Flow:	301 gpm	1140 l/min	319 gpm	1210 l/min
Flow per Nozzle:	15.1 gpm	57 l/min	16.0 gpm	61 l/min
System Pressure:	134 psi	9.2 bar	150 psi	10.5 bar
Blast Velocity:	141 ft/sec	43 m/sec	149 ft/sec	45 m/sec
Power Density:	.51 hp/ft³	12 kW/m³	0.68 hp/ft³	16 kW/m³

 

UPGRADES: (DUPLEX)	55 hp (US)	41 kW (Metric)	70 hp (US)	52 kW (Metric)
Total System Flow:	356 gpm	1350 l/min	371 gpm	1400 l/min
Flow per Nozzle:	17.8 gpm	67 l/min	18.6 gpm	70 l/min
System Pressure:	187 psi	12.9 bar	203 psi	14 bar
Blast Velocity:	166 ft/sec	51 m/sec	173 ft/sec	53 m/sec
Power Density:	.93 hp/ft³	22 kW/m³	1.19 hp/ft³	28 kW/m³

 

Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.