5275 StingRay Parts Washer

Retractable Turntable Aqueous Parts Washers

The StingRay 5275 industrial parts washer is engineered for tough aqueous cleaning applications. The large 52 inch diameter turntable and tall 75 inch working height allows easy & reliable cleaning for large parts. The 5275 parts washer uses high power density for fast wash cycles and high temperature operation for removing tough soils in short wash cycles. Used in rail, over the road and off road rebuilding of engines, transmissions and associated parts. Automated cycle of the aqueous parts washer uses hydraulic force and the patented oscillating spray manifold to overpower tough soils. Other parts washing applications include electric motor cleaning and removing ink from totes.

• Green Technology: Closed Loop Zero Discharge
• Heavy 7 gauge (3/16 inch) thick cabinet walls and reservoir
• Swing Door Retracting Turntable for Maximum Access
• Electronic Water Level Control & Refill
• Oscillating Wash Manifold to Maximize Cleaning
• Easy to Service Front Wash Pump Suction Strainer
• Adjustable Electronic Temp Control, Temp Gauge
• Control Transformer External of Panel minimizes Heat
• Programmable 24 Hour 7 Day Clock
• Low Water Shut-off Protects Pumps & Heating System
• Electronic Door Safety Interlock
• Wash Cycle Timer with Auto Reset
• Heavy gauge 3/16" Sheet Steel Cabinet Thickness
• 208V, 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
• 50 Hertz 380V and other worldwide voltages available
• Chemical Resistant Two Part 3 mil Epoxy Coating

 

Work Area Dimensions:	US	Metric
Turntable Diameter:	52 inches	1320 mm
Work Height:	75 inches	1900 mm
Table Load Capacity:	4000 lbs	1810 kg
Heavy Duty Capacity:	7000 lbs	3170 kg

Overall Dimensions:	US	Metric
Width: (Std Unit)	98 inches	2480 mm
Depth: (Std Unit)	87 inches	2200 mm
Height:	120 inches	3040 mm
Empty Weight:	6100 lbs	2770 kg
Reservoir Capacity:	265 gallons	1000 liters
Duplex Reservoir:	Add 47 gallons	Add 178 liters
Sludge Capacity:	75 gallons	284 liters

Spray Blast Manifold:
OSCILLATING NON-SYNCHRONOUS
Angle of Oscillation: (Picture)	39 Degrees
Frequency of Oscillation:	4 per minute
Number of Wash Nozzles: (Picture)	24
Type of Nozzle:	V-Jet
Nozzle Material:	316 Stainless

Heating System:	US	Metric
Operating Temperature:	140-190 degrees F	60-88 degrees C
Initial Heat up Time:	60-90 minutes	60-90 minutes
Electric Heat Element Size: (Picture)**	60 kW	60 kw
Gas / Propane (Picture)	400,000 BTU/hr	117 kW

Electrical Panel (Picture)	US	Metric
Motor Starters:	Across the Line	IEC Type 2
Short Circuit Protection:	Std	Coordinated
Overload Protection:	Std	Thermal Class 10
Electrical Enclosures:	NEMA 12	IP65
Wiring Standard:	NFPA 79	NFPA 79
Wiring Conduit:	Flex-Non-Metallic	Flex-Non-Metallic
Conduit Type:	Liquidtight NEMA 12	Liquidtight IP65

Pump System & Performance:
Motor Type: (Picture)	Industrial
Motor Rating:	Continuous Duty
Motor Enclosures:	TEFC

High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.

Standard:	30 hp (US)	22 kW (Metric)
Total System Flow:	343 gpm	1300 l/min
Flow per Nozzle:	14.3 gpm	54 l/min
System Pressure:	121 psi	9.3 bar
Blast Velocity:	133 ft/sec	41 m/sec
Power Density:	0.33 hp/ft³	8 kW/m³

 

UPGRADES: (DUPLEX)	55 hp (US)	41 kW (Metric)	70 hp (US)	52 kW (Metric)
Total System Flow:	399 gpm	1510 l/min	431 gpm	1630 l/min
Flow per Nozzle:	16.6 gpm	63 l/min	18.0 gpm	68 l/min
System Pressure:	163 psi	11.2 bar	190 psi	13.1 bar
Blast Velocity:	155 ft/sec	47 m/sec	168 ft/sec	51 m/sec
Power Density:	.6 hp/ft³	14 kW/m³	.76 hp/ft³	18 kW/m³

 

Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.