Heavy Duty Retractable Turntable Parts Washer
The StingRay 60112 aqueous parts washer offers an impressive work area, parts washer power density and impact pressure to wash larger Caterpillar engine blocks and EMD locomotive blowers. The oscillating power wash manifold removes the toughest soils eliminating secondary parts washing procedures. Typical industrial parts washing applications include large diesel engine blocks and aircraft landing gear components.
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 3/16" Sheet Steel Cabinet Thickness
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
60 inches |
1520 mm |
| Work Height: |
112 inches |
2840 mm |
|
Table Load Capacity:
|
7500 lbs |
3400 kg |
| Heavy Duty Capacity: |
15000 lbs |
6800 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
106 inches |
2690 mm |
| Depth: (Std Unit) |
91 inches |
2310 mm |
| Height: |
162 inches |
4110 mm |
| Empty Weight: |
7150 lbs |
3240 kg |
| Reservoir Capacity: |
350 gallons |
1325 liters |
| Duplex Reservoir: |
Add 47 gallons |
Add 178 liters |
| Sludge Capacity: |
80 gallons |
303 liters |
| Spray Blast Manifold: |
| OSCILLATING NON-SYNCHRONOUS Video |
| Angle of Oscillation: (Picture) |
39 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
24 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
120-140 minutes |
120-140 minutes |
| Electric Heat Element Size: (Picture)** |
80 kW |
80 kw |
| Gas / Propane (Picture) |
550,000 BTU/hr |
161 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
IEC Type 2 |
| Short Circuit Protection: |
Std |
Coordinated |
| Overload Protection: |
Std |
Thermal Class 10 |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
NFPA 79 |
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| Standard: |
30 hp (US) |
22 kW (Metric) |
| Total System Flow: |
343 gpm |
1300 l/min |
| Flow per Nozzle: |
14.3 gpm |
54 l/min |
| System Pressure: |
121 psi |
8.3 bar |
| Blast Velocity: |
133 ft/sec |
41 m/sec |
| Power Density: |
0.16 hp/ft³ |
6 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
70 hp (US) |
52 kW (Metric) |
| Total System Flow: |
399 gpm |
1510 l/min |
431 gpm |
1630 l/min |
| Flow per Nozzle: |
16.6 gpm |
63 l/min |
18 gpm |
68 l/min |
| System Pressure: |
163 psi |
11.2 bar |
190 psi |
13.1 bar |
| Blast Velocity: |
155 ft/sec |
47 m/sec |
168 ft/sec |
51 m/sec |
| Power Density: |
0.3 hp/ft³ |
7 kW/m³ |
0.38 hp/ft³ |
9 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
