Parts Washers

StingRay 6048 Parts Washer - Retractable Turntable

The 6048 parts washer not only offers an impressive power density for cleaning but also our patented oscillating manifold to fit into any application. Together this washer is a must for any DC and AC electric motor rebuilder. It is also used by blenders of ink and paint to wash tubs, totes and pails thoroughly and cost effectively. For tougher cleaning in larger diesel transmission, diesel engine and carrier rebuild shops we offer our high output electric heat and gas/propane eclipse burner system these both have been engineered to provide the user the best cleaning possible.

Electric Motor Parts Washer

Standard Features & General Construction:

SR 6048 Parts Washer
Printer Version PDF

Green Technology: Closed Loop Zero Discharge
Swing Door Retracting Turntable for Maximum Access
Electronic Water Level Control & Refill
Oscillating Wash Manifold to Maximize Cleaning
Easy to Service Front Wash Pump Suction Strainer
Adjustable Electronic Temp Control, Temp Gage
Control Transformer External of Panel minimizes Heat
Programmable 24 Hour 7 Day Clock
Low Water Shut-off Protects Pumps & Heating System
Electronic Door Safety Interlock
Wash Cycle Timer with Auto Reset
Heavy gage 3/16" Sheet Steel Cabinet Thickness
230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
Chemical Resistant Two Part 3 mil Epoxy Coating

Work Area Dimensions:

Metric

Turntable Diameter:

Work Height:

Table Load Capacity:

Heavy Duty Capacity:

60 inches

48 inches

3000 lbs

7000 lbs

1520 mm

1210 mm

1359 kg

3171 kg

Overall Dimensions:

Metric

Width: (Std Unit)

Depth: (Std Unit)

Height:

Empty Weight:

Reservoir Capacity:

Duplex Reservoir:

Sludge Capacity:

106 inches

91 inches

93 inches

6650 lbs

350 gallons

Add 47 gallons

80 gallons

2690 mm

2310 mm

2360 mm

3012 kg

1325 liters

178 liters

303 liters

Spray Blast Manifold:
OSCILLATING NON-SYNCHRONOUS (Video)

Angle of Oscillation: (Picture)

Frequency of Oscillation:

Number of Wash nozzles: (Picture)

Type of Nozzle:

Nozzle Material:

Nozzle Spray Pattern:

39 Degrees

4 per minute

V-Jet

316 Stainless

25 degrees

Heating System:

Metric

Operating Temperature:

Intitial Heatup Time:

Electric Heat Element Size: (Picture)

Gas / Propane (Picture)

140-190 degrees F

60 - 90 minutes

60 kW

400,000 BTU/hr

60-87 degrees C

60 - 90 minutes

60 kw

117 kW

Electrical Panel (Picture)

Metric

Motor Starters:

Short Circuit Protection:

Overload Protection:

Electrical Enclosures:

Wiring Standard:

Wiring Conduit:

Conduit Type:

Across the Line

Std

NEMA 12

NFPA 79

Flex-Non-Metallic

Liquidtight NEMA12

Across the Line

Std

IP65

Flex-Non-Metallic

Liquidtight IP65

Pump System & Performance:
Motor Type: (Picture) Motor Rating: Motor Enclosures:	Energy-Efficient Continuous Duty TEFC

High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.

STANDARD:			UPGRADES: (SIMPLEX)
		20 hp		30 hp		40 hp
	US	Metric	US	Metric	US	Metric
Total System Flow: Flow per Nozzle: System Pressure: Blast Velocity: Power Density:	269 gpm 13.5 gpm 107 psi 126 ft/sec 0.25 hp/ft³	1017 l/min 51 l/min 7 bar 38 m/sec 6 kW/m³	301 gpm 15.1 gpm 134 psi 141 ft/sec 0..38 hp/ft³	1138 l/min 57 l/min 9 bar 43 m/sec 9 kW/m³	319 gpm 16.0 gpm 150 psi 149 ft/sec 0.51 hp/ft³	1206 l/min 61 l/min 10 bar 45 m/sec 12 kW/m³

	UPGRADES: (DUPLEX)
		55 hp		70 hp
	US	Metric	US	Metric
Total System Flow: Flow per Nozzle: System Pressure: Blast Velocity: Power Density:	356 gpm 17.8 gpm 187 psi 166 ft/sec 0.7 hp/ft³	1346 l/min 67 l/min 13 bar 51 m/sec 17 kW/m³	371 gpm 18.6 gpm 203 psi 173 ft/sec 0.89 hp/ft³	1402 l/min 70 l/min 14 bar 53 m/sec 21 kW/m³

Results may vary based on machine configuration

StingRay 6048 PARTS WASHER
Optional Features:

PARTS WASHER Productivity
Pump Upgrades
Pump Amp Meter
Closed Loop Rinse System
Rinse Rust-Inhibtor Injector System
Remote Grease Lubrication Points
Automatic Lubrication System
Hand Rinse Wand
Turntable load Capacity Upgrade
High Output Electric Heat + 15 kW
High-Low Pressure Switch (Duplex)
Turntable Jog
Hour Meter

PARTS WASHER Configuration
Gas Burner Option
Auto Steam Exhaust
Steam Exhaust PVC Flange Kit
Center Manifold Probe
Short High Impact Manifold (Video)
Hot-Air Blow-Off
High Speed Evaporation Drying
Pump Pressure Regulator
Stretched Work Height Mild Steel
Stretched Work Height Stainless Steel
Stainless Steel Cabinet
Stainless Steel Heat Exchanger
Aircraft Cleaning Designed SS Washer
Heavy Duty Duplex Pump
50 Hz Engineered System

PARTS WASHER Solution Management
Auto Oil Skimmer
Heated Oil Skimmer
Sludge Drag Out Conveyor
Airlift System
Solution Transfer Pump
Sludge Pump Cart
In-Line Filtration
Oil Coalescing System

PARTS WASHER Safety
Pump Sound Barrier
Industrial Control & Safety Disconnect

PARTS WASHER Material Handling
Parts Cleaning Baskets
Parts Cleaning Fixtures
Parts Loading Jib Crane
Parts Cleaning Tie-Downs

PART WASHER Energy Conservation Cabinet Thermal Insulation
Internal Reservoir Cover

StingRay Manufacturing LLC
111 West Port Plaza, Suite 600
St. Louis, MO 63146

Phone # 314-447-9000
Fax # 314-447-0909
e-mail - sales@stingwash.com