Large Retractable Turntable Parts Washer
The StingRay 8473 industrial parts washer not only offers an impressive parts washer power density for parts cleaning but also the patented oscillating power wash manifold to maximize parts cleaning in any industrial application. The large diameter turntable and high load capacity of this heavy duty parts washer is ideal for cleaning diesel engine blocks, wind turbine gear drives and power transmission, large industrial pump bodies and aerospace landing gear components. The StingRay 8473 parts washer is also used in the US nuclear industry.
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge
- Swing Door Retracting Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Oscillating Wash Manifold to Maximize Cleaning
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Temp Control, Temp Gauge
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- Heavy gauge 1/4" Plate Steel Cabinet Thickness
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: |
US |
Metric |
| Turntable Diameter: |
84 inches |
2130 mm |
| Work Height: |
73 inches |
1850 mm |
|
Table Load Capacity:
|
10000 lbs |
4530 kg |
| Heavy Duty Capacity: |
20000 lbs |
9060 kg |
| Overall Dimensions: |
US |
Metric |
| Width: (Std Unit) |
143 inches |
3630 mm |
| Depth: (Std Unit) |
125 inches |
3170 mm |
| Height: |
139 inches |
3530 mm |
| Empty Weight: |
15850 lbs |
7190 kg |
| Reservoir Capacity: |
775 gallons |
2934 liters |
| Duplex Reservoir: |
Add 56 gallons |
212 liters |
| Sludge Capacity: |
151 gallons |
572 liters |
| Spray Blast Manifold: |
| OSCILLATING NON-SYNCHRONOUS Video |
| Angle of Oscillation: (Picture) |
39 Degrees |
| Frequency of Oscillation: |
4 per minute |
| Number of Wash Nozzles: (Picture) |
24 |
| Type of Nozzle: |
V-Jet |
| Nozzle Material: |
316 Stainless |
| Heating System: |
US |
Metric |
| Operating Temperature: |
140-190 degrees F |
60-88 degrees C |
| Initial Heat up Time: |
90-120 minutes |
90-120 minutes |
| Electric Heat Element Size: (Picture)** |
120 kW |
120 kw |
| Gas / Propane (Picture) |
800,000 BTU/hr |
229 kW |
| Electrical Panel (Picture) |
US |
Metric |
| Motor Starters: |
Across the Line |
Across the Line |
| Short Circuit Protection: |
Std |
Std |
| Overload Protection: |
Std |
Std |
| Electrical Enclosures: |
NEMA 12 |
IP65 |
| Wiring Standard: |
NFPA 79 |
|
| Wiring Conduit: |
Flex-Non-Metallic |
Flex-Non-Metallic |
| Conduit Type: |
Liquidtight Nema 12 |
Liquidtight IP65 |
| Pump System & Performance: |
|
| Motor Type: (Picture) |
Energy-Efficient |
| Motor Rating: |
Continuous Duty |
| Motor Enclosures: |
TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| Standard: |
30 hp (US) |
22 kW (Metric) |
| Total System Flow: |
343 gpm |
1300 l/min |
| Flow per Nozzle: |
14.3 gpm |
54 l/min |
| System Pressure: |
121 psi |
8.3 bar |
| Blast Velocity: |
133 ft/sec |
41 m/sec |
| Power Density: |
0.13 hp/ft³ |
3 kW/m³ |
| UPGRADES: (DUPLEX) |
55 hp (US) |
41 kW (Metric) |
70 hp (US) |
52 kW (Metric) |
| Total System Flow: |
399 gpm |
1510 l/min |
431 gpm |
1630 l/min |
| Flow per Nozzle: |
16.6 gpm |
63 l/min |
18 gpm |
68 l/min |
| System Pressure: |
163 psi |
11.2 bar |
190 psi |
13.1 bar |
| Blast Velocity: |
155 ft/sec |
47 m/sec |
168 ft/sec |
51 m/sec |
| Power Density: |
0.23 hp/ft³ |
5 kW/m³ |
0.3 hp/ft³ |
7 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
