Retractable Turntable Aerospace Wheel Parts Washer
The StingRay 4036 Aircraft Wheel Washer provides high parts washer power density and the unique oscillating power wash manifold to thoroughly remove rubber bead, carbon dust, grease, oil and soils in quick cycles from Aircraft Wheels. Working closely with the US military and other end users in the airline and aerospace industry, StingRay Engineering developed this wheel cleaning system for washing aircraft wheels for inspection and rebuild. The StingRay 4036 parts washer features a fully automatic cleaning cycle with wash, rinse and dry cycles for aerospace wheels and aircraft brakes. The wheel washer system yields four to six clean and dry aircraft wheel halves in a closed loop cycle per hour. Additional details are available in the case study on Aircraft Wheel Cleaning in the parts washer applications section.
USA Specifications:
SR 4036Parts Washer
Metric Specifications:
SR 4036Parts Washer
Standard Features & General Construction
- Green Technology: Closed Loop Zero Discharge & High Efficiency
- Stainless Steel Cabinet & Wetted Standard Components
- Heavy gage 3/16" Stainless Steel Cabinet Thickness
- Pump with Stainless Steel Shafts, Fasteners and Viton Seals
- Auto Fresh Water Heated Rinse Cycle
- Auto Steam Exhaust System
- Auto Programmable Oil Skimmer System
- Engineered Wheel Wash Power Blast Manifold
- Oscillating Washer Manifold Nozzles to Maximize Cleaning
- 2 Station Aircraft Wheel Washing Fixture
- Removable Internal Reservoir Cover allows Full Access to reservoir
- Swing Door Automatic Retracting Parts Washer Turntable for Maximum Access
- Electronic Water Level Control & Refill
- Easy to Service Front Wash Pump Suction Strainer
- Adjustable Electronic Digital Temp Control, 2 line displaypresent value & set-point
- Control Transformer External of Panel minimizes Heat
- Programmable 24 Hour 7 Day Clock
- Low Water Shut-off Protects Pumps & Heating System
- Electronic Door Safety Interlock
- Wash Cycle Timer with Auto Reset
- 230 V or 460 V - 60 Hz 3-Phase with 120 V Controls, 50 Hz optional
- 208VAC or 575 VAC options, Internataional 50hz 380/415VAC
- Chemical Resistant Two Part 3 mil Epoxy Coating
| Work Area Dimensions: | US | Metric |
| Turntable Diameter: | 40 inches | 1016 mm |
| Work Height: | 36 inches | 914 mm |
|
Table Load Capacity: |
1800 lbs | 818 kg |
| Overall Dimensions: | US | Metric |
| Width: (Std Unit) | 79 inches | 2010 mm |
| Depth: (Std Unit) | 74 inches | 1890 mm |
| Height: | 80 inches | 2030 mm |
| Empty Weight: | 4450 lbs | 2020 kg |
| Reservoir Capacity: | 180 gallons | 680 liters |
| Sludge Capacity: | 47 gallons | 178 liters |
| Spray Blast Manifold: | |
| OSCILLATING NON-SYNCHRONOUS Video | |
| Angle of Oscillation: (Picture) | 39 Degrees |
| Frequency of Oscillation: | 4 per minute |
| Number of Wash Nozzles: (Picture) | 16 |
| Type of Nozzle: | V-Jet |
| Nozzle Material: | 316 Stainless |
| Heating System: | US | Metric |
| Operating Temperature: | 140-190 degrees F | 60-87 degrees C |
| Initial Heat up Time: | 60-90 minutes | 60-90 minutes |
| Electric Heat Element Size: (Picture)** | 30 kW | 30 kw |
| Gas / Propane (Picture) | 180,000 BTU/hr | 53 kW |
| Electrical Panel (Picture) | US | Metric |
| Motor Starters: | Across the Line | Across the Line |
| Short Circuit Protection: | Std | Std |
| Overload Protection: | Std | Std |
| Electrical Enclosures: | NEMA 12 | IP65 |
| Wiring Standard: | NFPA 79 | |
| Wiring Conduit: | Flex-Non-Metallic | Flex-Non-Metallic |
| Conduit Type: | Liquidtight Nema 12 | Liquidtight IP65 |
| Pump System & Performance: | |
| Motor Type: (Picture) | Energy-Efficient |
| Motor Rating: | Continuous Duty |
| Motor Enclosures: | TEFC |
High Efficiency, Rated for continuous duty (20 Start/hour without overheating), vertical, centrifugal, seal-less, balanced, enclosed impeller. Note: All performance data taken at nozzle discharge.
| STANDARD: | 40 hp (US) | 30 kW (Metric) |
|---|---|---|
| Total System Flow: | 16.8 gpm | 1040 l/min |
| Flow per Nozzle: | 16.8 gpm | 59 l/min |
| System Pressure: | 168 psi | 10 bar |
| Blast Velocity: | 159 ft/sec | 48 m/sec |
| Power Density: | 1.53 hp/ft³ | 4 kW/m³ |
| UPGRADES: (Duplex) | 55 hp (US) | 52 kW (Metric) |
| Total System Flow: | 303 gpm | 1150 l/min |
| Flow per Nozzle: | 18.9 gpm | 72 l/min |
| System Pressure: | 212psi | 14.6 bar |
| Blast Velocity: | 177 ft/sec | 54 m/sec |
| Power Density: | 2.10 hp/ft³ | 54 kW/m³ |
Results may vary based on machine configuration.
** Heating element sizes listed for 208, 240 & 480 volt systems. Sizes vary slightly for other voltages.
